M10 as a slug shooter

April 24 2017 at 5:54 PM
gubb33ps  (Login gubb33ps)

A bit of hope for the issue M-10 .22 to be a cast bullet shooter. NOT changing any of the parts/tuning of the M-10; rather than fitting the rifle to the bullets went abut fitting the bullets to the rifle.

photo 46474280-1f7e-4dfc-a05b-dfec45671791.jpg

Not great results, but encouraging for "make-do".

Only mold I have is too heavy/too long to stablize. Runs about .515" long, .225" before sizing, and 48.5gr. when cast from recovered airgun pellet scrap.

Would partly key hole, spread out over a really wide-wide area on a 20-25 yard target, and basically were worthless for any use.

So I borrowed some time on a firend's jewlery lathe and cut the rear section off, which came out to .440" length and 40.4gr. Also figured out a way to consistently roll-size them to .2225-.223" (although becasue it started off life as a big-bore slug knurling tool, it left cross-hatch patterns on the bullet shank).

photo 62f1d6eb-4458-4d87-b457-38c9de44c355.jpg

Did much better. Not "pellet accurate" but good enough to let me know there is hope for this rifle becomeing a 56-60 foot pound .22 slug shooter.

photo 7a67514d-b6bf-4670-b9c4-c480a09bbadd.jpg

NOT GOOD ENOUGH...but encoraging as I've not got a standard barrled .22 PCP to shoot home-brew slugs nearly as well as this. Point on, no sight of tipping, and an at least "useful" group size.

There is PLENTY WRONG with these make-shift bullets. They are not all that uniform in diameter, the cross hatching bothers me, and there is WAY TOO MUCH unsupported "nose" for the bearing area. (50 years of cast bullet shooting tells me that that much un-supported by rifleing weight is just not a great thing.)

Converted another batch of them, taking much more care to get the length/weight just right, adjusted the make do knurler/sizer a little bit, and rubbing some lube into that cross hatched surface (just looked like it was made to hold lube).

photo 62f1d6eb-4458-4d87-b457-38c9de44c355.jpg

May be commerically cast/sized slugs that will out-shoot this by a whole lot...may not be. At least I can make these as often as I want to with the stuff I already have on hand.
Am going to just go ahead with what I can "make-do" at home. Can make as many more as I need to, have the mold...got my old mini-lathe woring...and borrowed the knruling/sizer.

If sized to somthing like .2225-.2227", can chamber them by pushing on the end of the bolt with your left had, and pushing on the bolt handle with your right hand (assuming you are right handed).
So this is what one like hand-chambered and pushed out by a rod. It takes a little "ooph" to chamber,but can do it with strong hands.

photo bf925631-05cb-4b1c-ba43-b3d3b6759535.jpg

Stiff chambering, but can chamber the slugs and achieve full rifling engagment. Kicking the nearly pure lead slug in the arse with 3K air pressure isn't going to hurt things.

photo e341408f-f0ae-4a46-9b25-eaaf0d37d56e.jpg

I'll cast up another 200 or so, closely insperct them an likely end up with 150-155 that "pass close visual inspection", convert them to diameter and length, and let it go at that until I run out of those 150-160 "sugs"...considering the number of shots "in anger" per year, that might well be somthing like 2020.

I kind of like this....a type of self-sufficicenty...can foot pump up the air prressure and cast the "slugs" it shoots.

 Respond to this message   



JK's Airgun Forums, moderators, and administrators are not responsible for any problems that may occur from reading or using content posted on this forum, as they are the exclusive responsibility of two parties: the person who posted it and the person who acted on said posted information.Use of our forums by people under 18 years old is allowed only with legal guardian(s) present..