The (new) Crosman Forum, your first and last stop for all things Crosman

 photo 63f5b325-0274-4312-9dbd-2effde5b3715_zps0x27orls.jpg

Alan Alford's build

2250b Tube for later move to bulk CO2.
12" .22 Caliber Barrel from Doomsday Backpacker
Brian & Assoc. Alluminum Breech with 2 barrel screws
Original site rear
Pin site on Custom Mt. Airguns Muzzle Break
2x1 Centerpoint Scope with UTG dovetail adapters
Mountain Airguns Custom Bolt and Handle
Mountain Airguns Custom Power Adapter and spring guide
B&A Boss Valve for extra Power

Built mainly for fun and to shoot at local Field Trial Pistol Match.

It currently it shoots a 14.3 Crosman Hunting Pellet at about 530 fps in a 72 degree room for 8.92 FPE.

  << Previous Topic | Next Topic >>Return to Index  

39X trigger assy

September 22 2011 at 9:03 AM
casey  (Login chaldeman1984)
Crosman Forum Member
from IP address

So I managed to pick up a 392 at a great discount simply because the rear sight was broken. I planned to and did end up putting a nice scope on it. Of course, however, it had the infamous late model 39X horrible trigger plauge. I tried filing on it, but now its to the point that I can file no more without random misfires because the hammer just barely catches on the sear from all the filing I did.

I was wondering if I could send someone the whole trigger assy and get it fixed up for a decent price. I like little bit of travel in a trigger whith a very light crisp break at the end. Even If I can't get a whole reworked trigger, even just a better sear would be great, but I don't know where or who to get them from. Again though, I have very little money for this, so I need something affordeable. If I have to buy a new sear from Crosman, I might as well sell the thing because when you have to pull that hard on the stock trigger it's extremely difficult to hold the gun still to aim.

any response would be appreciated.


 Respond to this message   

(Login airgunandy)
Crosman Forum Member

Airguns of Arizona

September 22 2011, 9:09 AM 

AoA sells a replacement sear for late model Benji rifles.

Also, check this out....

I plink, therefore I am.

 Respond to this message   

Steve in NC
(Login pneuguy)
Troll, Banned User or Assorted Delinquent

Here are two possibilities.

September 22 2011, 9:12 AM 

1. Start over with a new sear and modify it according to the method described here: The result won't improve the creep of the phony-2-stage Benji trigger (none of the popular mod's do), but at least you'll have a much lighter pull.

2. Buy one of my SuperSears from AoA:

The result will be exactly the kind of true 2-stage trigger you want.


This message has been edited by pneuguy from IP address on Sep 22, 2011 9:13 AM

 Respond to this message   
(Login chaldeman1984)
Crosman Forum Member


September 22 2011, 9:45 AM 

I just ordered a supersear. Hope it works out good.

As far as that valve mod on that link, how does one even get the valve out of a 39X?

 Respond to this message   

Steve in NC
(Login pneuguy)
Troll, Banned User or Assorted Delinquent

Removing the valve is easy.

September 22 2011, 10:20 AM 

1. Open the pump arm.

2. Remove the trigger assembly (you obviously already know how to do this happy.gif), spring, hammer, and stock lug (which is also what retains the valve and trigger assembly.

3. Pump.

Air pressure will pop the valve out.


 Respond to this message   
  << Previous Topic | Next Topic >>Return to Index  

Crosman Corporation 1-800-724-7486
This forum is not affiliated with the Crosman Corporation in any way// Information presented in this forum is intended for informational purposes only; use at your own risk//Posts made to this forum are soley the opinion of the individual member