<< Previous Topic | Next Topic >>Return to Index  

For sale: Microtech MTX-8 ecu, handset and loom

September 11 2015 at 11:58 PM
No score for this post
blaynefh  (Login blaynefh)
from IP address 101.190.158.250

 
Hi,

Up for sale is my Microtech MTX-8 ecu, handset, cable and wiring loom to suit FJ20ET. It is second hand but in good working condition. The loom has been fitted to my FJ20ET but everything is there to wire it up in another FJ20ET application. I purchased this ecu back in about 2004 and it has never let me down.

Current tune on it is for E85, 38psi boost and was making around 350rwkw in my Datsun 1600 drag car. Ran a PB of 10.83 @ 131mph using this ECU and the tune that's currently on it in December 2014. However can be tuned to whatever FJ20ET application you require.

Only selling due to upgrade so I can run more boost, timing and actually log whats going on inside the engine.

Price $450 ono for everything. Located in Sydney, N.S.W but will post interstate.

Regards,
Blayne
0416 538 440

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
AuthorReply
Anonymous
(no login)
58.164.17.52

Re: For sale: Microtech MTX-8 ecu, handset and loom

No score for this post
September 13 2015, 3:08 PM 

What r u upgrade to mate look at doing the some just don't know what ECU to upgrade to

 
Scoring disabled. You must be logged in to score posts.
Anonymous
(Login blaynefh)
101.190.189.196

Re: For sale: Microtech MTX-8 ecu, handset and loom

No score for this post
September 14 2015, 11:23 AM 

Upgrading to Haltech ps1000 and M&W CDI ignition system

 
Scoring disabled. You must be logged in to score posts.
Anonymous
(no login)
163.189.7.40

Re: For sale: Microtech MTX-8 ecu, handset and loom

No score for this post
September 25 2015, 3:37 PM 

Hey mate just curious what kind of box and diff setup you run in you 1600 drag car??

Auto or Manual? What box?

IRS rear end? if so what ratio R200?Locked or LSD?

Cheers


 
Scoring disabled. You must be logged in to score posts.
blaynefh
(Login blaynefh)
1.128.96.4

Re: For sale: Microtech MTX-8 ecu, handset and loom

No score for this post
October 30 2015, 11:11 AM 

I run a 3 speed GMH trimatic, full manual valve body, transbrake, 4000rpm converter. 3" Holden v8 tailshaft.Rear end is still IRS with 3.9:1 R200 LSD with rebuilt and shimmed clutch pack. CV drive shafts 4340 chromoly shafts

 
Scoring disabled. You must be logged in to score posts.
Anonymous
(Login shandawg)
121.98.128.144

Re: For sale: Microtech MTX-8 ecu, handset and loom

No score for this post
December 2 2015, 7:10 PM 

Hi mate would you mind putting it in a box and send to New Zealand? Need to get my R30 running properly and probably much easier to do this than persevere with the stock stuff.

Thanks

 
Scoring disabled. You must be logged in to score posts.
Anonymous
(no login)
58.106.67.85

Re: For sale: Microtech MTX-8 ecu, handset and loom

No score for this post
December 8 2015, 7:47 PM 

Dear MR shandawg
you made my day
thank you


 
Scoring disabled. You must be logged in to score posts.
shandawg
(Login shandawg)
47.72.183.218

Re: For sale: Microtech MTX-8 ecu, handset and loom

No score for this post
January 13 2016, 1:40 PM 

Glad I could be of service MR Anonymous

Blayne did you end up selling this?

 
Scoring disabled. You must be logged in to score posts.
 
  Respond to this message   
  << Previous Topic | Next Topic >>Return to Index  
Find more forums on Network54Create your own forum at Network54
 Copyright © 1999-2018 Network54. All rights reserved.   Terms of Use   Privacy Statement