<< Previous Topic | Next Topic >>Return to Forum  

1000X Piston Seal Help

August 2 2005 at 9:01 PM
Average Score 3.0 (2 people)
  (Login JohnGlennC5)
from IP address 216.130.10.4

 
Has anyone replaced the piston seal on this gun?
(Turkish model) My seal is in bad shape.
Where to buy and part numbers appreciated.

Daisy will not sell internal components for this gun.

Thanks.

BTW:
Polishing all of the mating surfaces of the trigger helps a lot. Sub 5 lbs possible. But I mean mirror finish.

Tight fitting spring guides front and rear make the shot cycle very sweet.

Cleaning, de-burring, polishing, lubing/mollying the internals helps a lot also.

I also ground more of a flat on the sping ends and polished them as well.

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
AuthorReply
Scottmi
(Login scottmi01)
Forum Owner
24.16.139.112

seals

Score 1.0 (1 person)
August 19 2005, 3:04 PM 

i've come across one or two sites/articles that commented on making your own new seals for airguns. you'll need to do that i think. search around and if/when you find a pertinent page, please post a link back here! if i come across them again, i'll do the same. there may even be standard 'stocked' sized of seals that you can use...

 
Scoring disabled. You must be logged in to score posts.Respond to this message   

(Login JohnGlennC5)
70.185.107.82

I re-sized a Webley Xocet seal

No score for this post
September 24 2005, 9:30 PM 

The Webley Xocet piston seal has just about exactly the same outside diameter as the stock Winchester seal when not in the gun
(approx. = 1.083 inches). The Xocet seal is also about 2mm taller.
[ http://www.airgunsofarizona.com ]

I eventually got the Xocet seal sized as good as I could (lots of sanding). I sized it to just slightly more of a snug fit than the stock seal because the stock seal was damaged (during assembly at the factory).

After function firing about 100 pellets, I recorded a 32 shot string.

I lost about 15 FPS with the new seal, it's now shooting CPLs at 868.8 FPS. That's not too bad. I suspect it will speed up a little as the new seal wears in.

Now for the crazy part (32 shot string):
Average = 868.8 FPS
Standard Dev. = 3.2 !!
Spread = 14.0 !!

The standard deviation and spread are unbelievable!
I can’t wait to see how it groups.

Later,
John
-----------------------------
9/24/2005
Crosman Premiers 7.9gr
FPS Shot #
874.4 1
869.2 2
869.7 3
862.7 4
869.8 5
868.8 6
870.3 7
873.1 8
870.0 9
866.4 10
870.6 11
868.3 12
869.7 13
868.5 14
868.9 15
876.7 16
871.6 17
868.4 18
871.6 19
870.1 20
863.8 21
868.9 22
868.4 23
868.8 24
864.3 25
870.0 26
863.2 27
871.6 28
870.9 29
864.8 30
865.9 31
863.4 32
----------------
868.8 average
3.2 std dev
876.7 max
862.7 min
14.0 spread

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
Current Topic - 1000X Piston Seal Help
  << Previous Topic | Next Topic >>Return to Forum  
Find more forums on Air GunsCreate your own forum at Network54
 Copyright © 1999-2009 Network54. All rights reserved.   Terms of Use   Privacy Statement  

Please keep your posts "On Target!"