Home > Discussion Groups > Axis

Message posting guidelines:

  • Full real names must be used at all times.

  • A valid e-mail address must be provided. (This is not optional)

  • Images must be posted at low resolution (72 dpi) and no larger than 760 pixels wide, and copyright/trade mark owners must be credited whenever reasonably possible.

  • Registration is compulsory if you wish to post messages on the Discussion Groups. For further information, please see the following message: http://www.network54.com/Forum/message?forumid=47207&messageid=1113822984

Please read our Community guidelines before posting.

By contributing to this discussion group, you indicate your agreement to the Terms and Conditions of Use.

Posts that violate the guidelines or Terms and conditions of Use of the Missing-lynx.com discussion groups will be erased, and repeated violation of this policy may result in termination of the violator's account.


Advertisement

  << Previous Topic | Next Topic >>Return to Index  

Question on Assembly of RB Tiger I Barrel Early......

June 8 2017 at 7:30 PM
Ron Hetherington  (Login veezerboy)
Missing-Lynx members
from IP address 104.35.220.3

No Instructions and none I can find on their site, so...........

Inside of the muzzle, the center part. It is long on one side, short on the other. Short side faces in??

Now for the 3 rings, 1 is solid and the other 2 are hill/valley (nut). One has a larger dia hole, so I'm guessing it goes on the long side, facing out, of the center part followed by the other similar looking part with the smaller dia?? This long side has a step in it. I guess the two together are for thickness....

Where does the solid ring go??


On Armorama someone asked the question and I think the answer is wrong with having 1 nut disk inside and the other out, which would not make it sit flush. The other solid ring is shown between the muzzle brake and the sleeve. That ring sits high and does not seem correct.

THANKS!!!

 
 Respond to this message   
AuthorReply
Ron Hetherington
(Login veezerboy)
Missing-Lynx members
104.35.220.3

Think I figured it out, though.........

June 8 2017, 9:21 PM 

Not sure where the solid ring goes, so just left it off.

center section is long side out and both nut rings go on this side.

 
 Respond to this message   
Arild Moland
(Login astralscooter)
Missing-Lynx members
94.139.87.154

Maybe this helps?

June 9 2017, 2:17 AM 

Looks to me like the Aber barrel has much the same parts breakdown as the RB Barrel, which means their instructions might help?

RB barrel (late version)

210228-12686-32-pristine.jpg

Aber instructions:

241ukbd.jpg

Arild

 
 Respond to this message   
Ron Hetherington
(Login veezerboy)
Missing-Lynx members
104.35.220.3

Thanks!! David, question for you then.......

June 9 2017, 7:09 PM 

I looked in my 131 Walk Around Book and saw it's Muzzle Brake so I just kind of went from there, but the picture above where the muzzle is shown being assembled, that ring between the Muzzle and Collar, is that really there?? From your post and the 131 book, I don't see the ring. Plus, it's edges sit higher so would be really strange having it there.

 
 Respond to this message   
David Byrden
(Login DavidByrden)
Missing-Lynx members
84.113.190.15

Aber's Part 3 ?

June 9 2017, 7:31 PM 

If that's what you mean, then I think there was a thin rubber ring there, for sealing. But it wouldn't protrude beyond the brake and collar.

David

 
 Respond to this message   
David Byrden
(Login DavidByrden)
Missing-Lynx members
84.113.190.15

Maybe this will help?

June 9 2017, 1:40 AM 



    
This message has been edited by DavidByrden from IP address 84.113.190.15 on Jun 9, 2017 1:41 AM


 
 Respond to this message   
 
  << Previous Topic | Next Topic >>Return to Index  


Terms and Conditions of Use
Report abuse