In other words THE HORSE is in no way responsible for any parts bought or sold on this board.
Off topic posts will be DELETED
Buyers and sellers of engines and frames should understand the legal status of the parts before the sale. Avoid problems and have the status understood up front. State conditions of the sale beforehand, and stick to the agreement. Parts known to be stolen or have bad numbers SHOULD NOT be bought or sold on The Horse Swap Board in the first place. Buyers beware but sellers be responsible. Long flaming posts clogging up the board are no fun. Avoid them by having all conditions understood and settled up front.
Please make sure you post PRICE AND LOCATION when selling parts.
Sorry, but due to psycho spam posters, you will now need to register to post.
tour pac wanted
Wanted a King tour pack to fit a 2006 FLH. Need everything: keys, wiring, mounting hardware etc. Must be in excellent condition, Black cherry paint would be nice. Let me know what you have. Please email as I don't always check the boards. Thanks
Posted on Dec 5, 2013, 12:10 PM from IP address 126.96.36.199
i have a 1983 fxr with an evo motor built in delkron cases , 2to1 exhaust cool old bike , needs some wiring. wanna trade for something i can ride,I value the bike at $6000 or so 2503214981 i can email pics jeff
Posted on Oct 25, 2013, 10:47 PM from IP address 188.8.131.52
but can always use more parts!!! would you consider sending me some pictures and your phone# cause this old hill-billy is trying to recover from 5th operation on right knee and have a hard time getting to my phone in time! lived in Montana for year and a half,but thats about as far north as i been,dont know how you boys stand that COLD!!! born and raised a Kentucky boy,been all over country but just touched Canada a time or two,enuff of that shit,how about them parts you holding? thanks later dragoo6951
Posted on Sep 2, 2013, 11:06 AM from IP address 184.108.40.206
Building,registering, and insuring a custom motorcycle in Ontario
Like the title says.how is this done in Ontario? I have a 2000 Buell and want to put it in a Paughco hardtail frame is this even feasible in Ontario? I cannot find anything on the MTO web site. Can someone point me in a good direction?
Posted on Aug 11, 2013, 9:51 PM from IP address 220.127.116.11
Re: Building,registering, and insuring a custom motorcycle in Ontario
good luck - been there done that. Getting the title is easy, showed my mso for the frame, my receipts for the engine and paid 10 bucks for a homebuilt title. I paid taxes on that only because I had already paid the taxes on the bike parts. The problem is that with a homebuilt title, your insurance goes through one company and it is through the roof. My insurance company was sold to the ONE, and subsequently my insurance is $2000 a year paid upfront. No way I', paying that so my bike is going up for sale. If it doesn't sell than I will buy a harley title and switch it all over and sell it. Do yourself a favour and keep the title in the buell's name. Not sure where the numbers on the buell are but I would try to somehow incorporate them into your new frame and lose your paucgho numbers. Either that or have someone cut up your buell frame. Those are the only two options I see.
Posted on Aug 13, 2013, 5:10 PM from IP address 18.104.22.168
Due to our noise law in Quebec,I'm buying all kind of stock exhaust system for Harleys customers...it has to be kind of clean,in ferfect shape with heat sheilds....let me know what you got at email@example.com
Want to see real Dogs ?
Want to see real Dogs ?
Posted on Apr 19, 2013, 7:19 AM from IP address 22.214.171.124
Complete bikes or parts . Engines, frames, transmissions, drum brake frontends, wheels , brakes. etc.
Off work lots of time to dig through for what you need.
Located in central Canada on the border.
Pictures on request
Posted on Dec 20, 2012, 3:41 PM from IP address 126.96.36.199
I'm interested in frames, titles, engines, trannys, front ends and all kinds of misc parts!!! I'm in the middle of a build, and my good buddy is just getting started. I'm in Windsor Ontario, Where are u???
Posted on Dec 23, 2012, 10:21 PM from IP address 188.8.131.52
I have a 48 U engine complete and a 44UL basket engine
by Alan (no login)
The unfortunate thing is it costs a lot to rebuild this stuff.
The 44 is cases, Aluminum heads, barrels and a few other pcs. But I do have an ontario ownership for it. So that helps if and when you get it on the road.
I'lll send some pictures your way.
But this stuff is not free.
Posted on Apr 2, 2013, 10:02 PM from IP address 184.108.40.206
Looking to Buy a Norton Commando, Atlas or Triumph Bonneville in Ontario. Must have had a documented engine and tranny rebuild. I don't care about cosmetics. Must be certifiable. Please help me get riding again this year! Thanks David Otto Stein
Posted on Mar 18, 2013, 3:39 PM from IP address 220.127.116.11
I heard about this on the way to work this morning...sad.
No go to P'borough for me, as much as I would like to.
R.I.P indeed...hope he's somewhere with a big ol slab of plywood to put his boot through.
Posted on Mar 7, 2013, 11:44 PM from IP address 18.104.22.168
I talked to the church...its on again!! Thanks to everyone that came out and supported last year!!! Same place, Evangel church, same contacts (arlene or Jed 345-3503) to book a table, or questions.
I felt it went well last year, a good turn out, good food, and some good deals. It was nice Hope to see you all again this year. It usually starts at 9am...so get there early to get the good picks.......
Once again for newbies....its a motorcycle swap meet at the Evangel church 1260 balmoral st. (inside there gym) SATURDAY MARCH 2nd 2013. If you have parts to sell contact Jed or arlene @ 345-3503 to book a table. If you only have a hand-full of parts, share a table with your buddy......
If you just want to buy parts, its 3 bucks admission to get in. Table rental is 20 bucks. All funds support the church....NOT ME. Any brands of motorcycle parts (honda, kawa, triumph, HD etc) or motorcycle related gear. motor clothes, helmets, and such are also encouraged.
Get rid of the winter blues and get excited about 2 wheeled debachery!!!! hope to see you there. I have enclosed my email.....if anyone has Q's. thanks to THBC for letting me post it!! Drew
Posted on Jan 22, 2013, 11:13 AM from IP address 22.214.171.124
I've got a 1969 Sportster that I'm in the process of restoring. I was
hoping to have it on the road this Spring, but I'm not sure now. So
what I'd like to do is get something that I can use for awhile, until
the Sportsters ready. I'm laid off for the Winter, so I'm strapped for
cash. I thought I 'd try a trade, just to see if there's any interest. I've
got one, possibly two 12 gauge doubles that I don't use much, that
I'd trade for a decent Jap bike, 650 or larger and preferably a twin.
I'd like something like an older Virago or an XS. If there's anybody
interested, I could e-mail some pics. I live in Owen Sound, Ont.
My number is (519)371-3679. Thanks. Ron
Posted on Feb 1, 2013, 7:58 PM from IP address 126.96.36.199
Nice setup. 10 spoke chrome mags large axle.
Metzler M E. 880 tires 140/70B18 . I was told you could change the bearings to run them on an older bike, I'm not sure about that. The wheels came of a 2001 road glide. 750. shipped
Posted on Jan 14, 2013, 8:02 PM from IP address 188.8.131.52
Looking to replace my 4 speed kick only with a complete 5 speed tranny setup(complete-tranny, starter, clutch etc..) that will work with my 1.5" open belt primary. Would also purchase just the 5 speed clutch basket if thats all you have. Looking for something hopefully local because I think shipping will be a killer. Might trade the 4 speed as partial if interested.
Posted on Oct 14, 2012, 9:36 AM from IP address 184.108.40.206
Hey Brian- my email address is Metalmeltdown@cogeco.ca
what I'm looking for is a 5 spd tranny complete with inner/outer primaries which I can cut up to work with my belt primary. I want to get a complete system with starter, compensator sprocket, clutch etc etc. I already have a 5 speed tranny plate and want to use my 1.5" open belt. So the clutch hub will need to work with a 1.5" belt primary and chain secondary. I basically want something that I have all the components from one person. I just put over $300 into my tranny, new 5 stud clutch basket, new friction plates, kickstart gears, kicker shaft, custom kicker(also have a chrome 4 speed ajuster plate with the jacking plate. let me know what you have, maybe some pics and we'll see if we can work something out.
Posted on Oct 24, 2012, 6:42 PM from IP address 220.127.116.11
bought a 85-89 softail 5 speed tranny. Still need to buy a clutch cable, clutch pushrod assembly, final drive chain sprocket assembly, clutch basket for a 1.5" belt, clutch. Prefer fairly local pickup. Whatcha got.
Posted on Nov 18, 2012, 10:14 AM from IP address 18.104.22.168
I've got a 1969 XLCH. It has no spark, so I'm assuming that it needs a new coil. I put on new Accel copper
plug wires and a new condenser. The points are good. Does anyone out there have a good coil to sell? I really want to get this thing going before my riding season is done. Thanks guys. Ron
Posted on Sep 19, 2012, 12:12 PM from IP address 22.214.171.124
Looking for a stainless cover with 4 stripes but would consider chrome.
V twin has had it on back order for some time.
Looking for very good condition .
Have a 3 stripe stainless for sale or trade if any one needs it.
Posted on Nov 2, 2012, 5:23 PM from IP address 126.96.36.199
I make solid silver or gold Shovelhead engine rings. I have 2 alternator shovel rings currently ready to go for $500 CAD each and have just finished carving and molding a generator version. I have for sale the silver generator ring from my master carving for $600 CAD. The regular generator rings out of the mold in silver will be $500 CAD. These rings weigh approximately 50 grams in sterling silver and 55-60 grams in gold. They have very thick shanks and solid filled backs. These are good solid handmade rings, not cheap taiwanese crap! I also have silver Shovel Cult skull rings for $300 CAD, they weigh 34 grams. The shovel pin pictured weighs 35 grams and has double brass screw backs, it's priced at $275 CAD. I'm located in Edmonton, Alberta, Canada. I accept paypal and will ship product promptly by the carrier of your choice. Prices do not include shipping.
Posted on Oct 18, 2012, 10:50 PM from IP address 188.8.131.52
motorcycle poker run in thunder bay, ON --SAT sept 29th
by drew (no login)
Short notice....hopefully someone reads this. Poker run starting @ 11am from Deluca's restaurant....downtown PA. 25 bucks gets you lunch, and dinner (pig roast/corn roast) and a poker hand. moneys raised go towards MS. Grass drag races, biker games, beer etc. come out for a rockn time!!! No HD sponsership or affiliation. prizes for best backyard scoot etc. Did i mention tequila and cigars as some of the prizes??? Come if you like to have fun....if your scared....stay at home. Contact "the Jew" for more info c-621-6610
Posted on Sep 27, 2012, 11:43 AM from IP address 184.108.40.206
let them go for $200 and a little for UPS. The carb alone for $150. It has a new inlet needle, and 72/.295 jets. You will probably want a smaller set of jets for the xl, You will need to tell me the displacement and other mods before I can rejet it.jThe manifold is O-ring not rubber band. If you need a rubber band style they run ~ $80 new. Post here and I'll check this eve.
Posted on Aug 8, 2012, 8:53 AM from IP address 220.127.116.11
I need a cast iron pump for a 1956 pan.
I have a v twin repop pump on the motor now. It will not return all the oil to the tank.
I have checked everything else so I'm going to try a stock pump.
Cash or parts what ever you need.
Posted on Jul 22, 2012, 9:50 AM from IP address 18.104.22.168
To get the most flow out of them, it is a good idea to swap out the gears in the cam case. Use 74 and later pinion oil-pump drive gear, and the mating gear on the pump shaft. These will run the pump~~20 percent faster, helping to offset the smaller pump gears the cast pumps have. It is a direct update, same keys, etc. Just thought to help that Pan!!!
Posted on Aug 5, 2012, 4:28 PM from IP address 22.214.171.124
Thanks, and note the later gears I mentioned in the thread above. They are a must if you want all you can get from these old pumps. If you can't find them up there, just let me know, as I carry them in stock. Happy trails on that Pan!!!
Posted on Aug 23, 2012, 12:08 PM from IP address 126.96.36.199
if you're interested, let me know, I'll send some pics this wknd...head breathers, I repainted them wrinkle black with (HD paint) they are bare, no valves...I know shipping would be alot because of weight (from Winnipeg), I'm not trying to get rich but if anyone's interested, make an offer
Posted on Jul 19, 2012, 12:07 PM from IP address 188.8.131.52
76 shovel motor. cases are a matched set of H.D. cases . Rebuilt by a shop never run.
80 cu. inch complete assembled engine.
New parts for charging system.
Used cv carb and rubber flange adapter.
Rebult e start 4 spd. trans. never run
Tech cycle belt drive and starter system.
Used rigid oil tank. Chrome or painted.
straight leg pan frame heavily cut up probably a 3 or 4 out of ten. Can be fixed or used as trading stock to get a titled frame.
Pan drum front end and 21 inch wheel and brake parts.
Pan drum rear wheel with backing plate and rigid axle for 57 frame.
Can add or delete parts from basket case .
Working on pictures.
NO OWNERSHIP bill of sale only these are swap meet parts.Shop receipts for labour and rebuild parts. This stuff was assembled to keep. No junk used.
Best offer. Shipping on you from central part of the country. I will crate or deliver within 500 miles for gas.
Posted on Apr 6, 2012, 11:09 AM from IP address 184.108.40.206
get rid of those silly hoses and stop shovin dirty air into the carb on yer evo big twin or your 91 up sportster. 1/2 13 tpi .AND NOW I HAVE THE SAME FOR TWIN CAM MOTORS. 3/4 HEAD WITH 3/8 16 TPI. for after market intakes. solid brass or 6061 aluminum. i make these in my garage with american materials. i offer these in any combo u like , brass with al ect. no one else offers em like this hit me up if u want a set
please let me know i can send invoice or you can paypal @ firstname.lastname@example.org but make sure u let me know what kind u want with what screen on the paypal payment. sometimes its a pain in the but to match id with email and paypal id
dont forget i also do longer ones to fit arlen or joker style cleaners only in the 1/2 13 style
please c my page @ meadows moto' machine on facebook
dont forget that i make kustom pegs and wheel spacers ect
meadows moto and machine
Posted on Jun 30, 2012, 9:49 AM from IP address 220.127.116.11