Login  /  Register  
  Home  -  Forum  -  Classifieds  -  Photos  -  Links     

  << Previous Topic | Next Topic >>Return to Index  

Ideas on low budget rotating upgrade for a 360?

October 4 2017 at 9:50 AM
Jim  (Login FormerlyCyclonic66)
Members

Not keen on scouring Craigslist for beat up 390 stuff that needs machining. Are there any reasonable "stroker" kits out there for a daily driver deal? I'm thinking 9:1 or so with Edelbrock heads.

 
 Respond to this message   
AuthorReply
Matt
(Login nandoz)
Members

I have a 390 crank and rods that are decent

October 4 2017, 10:46 AM 

I would sell them cheap. nandoz66@gmail.com

 
 Respond to this message   
paulie
(Login Paul_Lovett)
Members

You can find good factory 428 cranks for $400 or less.

October 4 2017, 6:54 PM 

That's my vote for a budget stroker.

JMO,

paulie

 
 Respond to this message   
winr1
(Login winr1)
Members

Rick has one for $500.00 shipped, was in a running mill he allows ..

October 4 2017, 7:00 PM 

http://www.network54.com/Forum/75943/thread/1507052848/last-1507052848/View+thread


Some aftermarket pistons are .030 in the hole

Mill .070 off and make a 0 deck 410 ..

Use stock rods as well




Ricky.


    
This message has been edited by winr1 on Oct 4, 2017 8:15 PM


 
 Respond to this message   
Bill Ballinger
(Login 65billgal)
Members

I hate beating on anything more than a 390 crank these days

October 8 2017, 4:51 PM 

The 428CJs needing them for restos. How much would a 4" stroke Scat be with 2.1 rod journals? I would love to have one with a 4.094 bore, or a 4.030 stroke with the small journals, 1.36 CH Mahle's with Metric rings and some Scat I beams about 6.8 long. That would be a nice 1.7 rod to stroke ratio and light pistons with a lot of dwell at TDC, and 421 ci. It lacks a few cubes but it would make a good 390 block shine if you had a good thick one, .044 over and a 4" stroke at zero. I wonder what that rotating assembly would be for an FE, it would be great for the heads, long rods like moderate flowing heads. Do up the BBMs at 12° use my SD that already has a wide port pinch. The C6 with the Spartan 4.33s would love that engine even at 1.2 lbs ft per cube and 1.28 hp per cube, that would be a blast!

Does Scat make a 4"-4.030" stroke 2.1 rod journal crank? Do they make 6.8 I-beams at that length? I think the 445s are using 1.36 CH pistons. It would be fun and it would be nice at 5800-6300 for hp. I would use a 294S advanced to 102-104°.

I really hope Billy gets the fire in the belly to drive the car, he bought a used wood steering wheel like a 7 litre would have only universal. We have the 3" pipe and X with Flw 40's to put on it. I just want to ride in it before I die.


    
This message has been edited by 65billgal on Oct 8, 2017 4:54 PM


 
 Respond to this message   

TorinoBP88
(Login TorinoBP88)
Members

Where are you?

October 7 2017, 9:36 AM 

I have an extra 428 crank and rods, if you are in Northern California. It's a pain to ship though.

 
 Respond to this message   
 
  << Previous Topic | Next Topic >>Return to Index