<< Previous Topic | Next Topic >>  

Recommendations for MROD/PROD performance parts?

March 18 2017 at 9:47 PM
Wayne  (Login waynejitsu)
YF

Who do you recommend for aftermarket performance parts for the MROD/PROD air guns?
Looking to "upgrade" a couple of 25's, a 177 MROD and 22 PROD
Power, shot count, adjustability, etc.
Thanks guys

 
 Respond to this message   
AuthorReply
Rick
(Login pluric)
YF12

My best suggestion..

March 18 2017, 11:16 PM 

.. a Marmot Militia barrel. Transformed my Prod
Power won't fix inaccuracy of a barrel.

http://marmotmilitia.com/index.html

[linked image]

[linked image]


    
This message has been edited by pluric on Mar 18, 2017 11:18 PM


 
 Respond to this message   
Jeremy
(Login Smaug1)
YF

I think I'm gonna go this way (MM barrel)

March 21 2017, 9:34 AM 

Maybe you saw my thread over on the GTA, because those targets look familiar. wink.gif

Everything I've read is folks doing stuff to finish the Crosman barrels. Polishing the rough crown, leade, inside. They just seem to be low quality barrels. I like the way the gun handles enough that I think I'm going to drop a few more bucks into it. (and stop buying Crosman products from now on)

My stock rested groups look just about like yours (a little bigger, as I was shooting @ 30) Not acceptable. Good enough to drill a squirrel at 10-15 yards, but not good enough to justify shooting a PCP, since even my cheap Summit shoots that well. ...and I wouldn't even feel comfortable taking a brain shot at 10 yards.

How hard is it to take the P-Rods apart? I changed barrels on my 2300T and lost the safety parts. When I separated the barrel/receiver assembly from the grip frame, they just flew out across the basement, never to be seen again.
-Jeremy
"If it's worth doing, it's worth OVERdoing."

 
 Respond to this message   
Rick
(Login pluric)
YF12

Prod barrel swap

March 22 2017, 9:10 AM 

It really can be done in minutes. I watched a youtube
video and it's quite simple from there. You don't have
to degas the gun. Just make sure the breech parts line
up dropping it back down and you are in accuracy heaven. happy.gif

 
 Respond to this message   
Tommy
(Login shambozzie)
YF12

Give Ronnie Easton @ Easton airguns a call........

March 19 2017, 7:38 AM 

Mrod,prod,1720, 1701 Ronnie is the man.

 
 Respond to this message   
Wayne
(Login waynejitsu)
YF

Thanks Guys!! :)

March 19 2017, 10:33 PM 

n/t

 
 Respond to this message   
TerryH
(Login TerryHatfield)
YF12

Upgraded valves etc...

March 23 2017, 3:29 PM 

Much performance gain to be had with lighter hammers, better flowing valves, bigger transfer ports etc.. also. I have Tim Hill's parts in my .22 cal Armada and the difference is big. Getting 70+ shots @ 30fpe now on a single fill.


    
This message has been edited by TerryHatfield on Mar 23, 2017 3:31 PM


 
 Respond to this message   
 
  << Previous Topic | Next Topic >>  

Airgun Calculators    Num of fills calc    Capacity Calc

******** Kalibrgun High quality, superb Accuracy, outstanding Value. ********





D I S C L A I M E R
JK's Airgun Forums, moderators, and administrators are not responsible for any problems that may occur from reading or using content posted on this forum, as they are the exclusive responsibility of two parties: the person who posted it and the person who acted on said posted information.Use of our forums by people under 18 years old is allowed only with legal guardian(s) present.