<< Previous Topic | Next Topic >>  

S4xx Fill and pressure gauge?

May 24 2017 at 11:52 AM

Rob in NC  (Login rob3dr)
AR&P

I know most S4xx's have the pressure gauge at the bottom, but my MPR-FT has none. Does anyone know of a pressure gauge/fill assembly that will mount on the front of the tube?

I've searched around and found nothing. I know one vendor says he is working on one that may be available in the coming months, but that's as close as I've gotten.

Thanks
____________________________________
All those who believe in psychokinesis, raise my hand.

Good judgment comes from experience; experience usually comes from bad judgment.

 
 Respond to this message   
AuthorReply
BillE.
(Login garczar)
YF12

Re: S4xx Fill and pressure gauge?

May 24 2017, 11:58 AM 

For that to work you'd need a fill assembly like a Cricket that uses a slip-in probe and end-mounted gauge. Would probably require a new pressure tube that is is threaded at the muzzle end to do this. Sounds doable but EXPENSIVE. BTW, when was you4 rifle made? The later MPR-FT's that i've seen all had gauge on bottom.
"\"\""


    
This message has been edited by garczar on May 24, 2017 12:04 PM


 
 Respond to this message   

Rob in NC
(Login rob3dr)
AR&P

I've seen after market ones

May 24 2017, 12:02 PM 

for the S200 guns, so I was hopeful there was something similar for the S400.

____________________________________
All those who believe in psychokinesis, raise my hand.

Good judgment comes from experience; experience usually comes from bad judgment.

 
 Respond to this message   
BillE.
(Login garczar)
YF12

Re: I've seen after market ones

May 24 2017, 12:09 PM 

I checked that and saw the Altaros S200 kit. Pretty cool. You must have a early MPR as all(4-5) i've seen all had gauges.
"\"\""

 
 Respond to this message   

Rob in NC
(Login rob3dr)
AR&P

Mine apparently was

May 24 2017, 12:15 PM 

the prototype to the MPR-FT. I picked it up off the Classifieds years ago for 600 bucks. I checked with Bori at the time and he confirmed it was the prototype, but aside from his confirmation, I have nothing else really. It looks largely the same as current models.

[linked image]
____________________________________
All those who believe in psychokinesis, raise my hand.

Good judgment comes from experience; experience usually comes from bad judgment.

 
 Respond to this message   
BillE.
(Login garczar)
YF12

Re: S4xx Fill and pressure gauge?

May 24 2017, 12:13 PM 

Just checked Altaros's site and they show a AA kit. Video shows it being put in a 400. Its listed in "other access." and is 64euro.
"\"\""

 
 Respond to this message   

Rob in NC
(Login rob3dr)
AR&P

thought I'd checked there...but..

May 24 2017, 12:16 PM 

will certainly check again. Thanks so much!
____________________________________
All those who believe in psychokinesis, raise my hand.

Good judgment comes from experience; experience usually comes from bad judgment.

 
 Respond to this message   

Rob in NC
(Login rob3dr)
AR&P

You are correct, sir!

May 24 2017, 12:19 PM 

It does show as being installed on an S4xx... bingo!
I just missed that first pass through. Thanks again!
____________________________________
All those who believe in psychokinesis, raise my hand.

Good judgment comes from experience; experience usually comes from bad judgment.

 
 Respond to this message   
 
  << Previous Topic | Next Topic >>  

Airgun Calculators    Num of fills calc    Capacity Calc

******** Kalibrgun High quality, superb Accuracy, outstanding Value. ********





D I S C L A I M E R
JK's Airgun Forums, moderators, and administrators are not responsible for any problems that may occur from reading or using content posted on this forum, as they are the exclusive responsibility of two parties: the person who posted it and the person who acted on said posted information.Use of our forums by people under 18 years old is allowed only with legal guardian(s) present.