For when it HAS to sell...
  << Previous Topic | Next Topic >>Return to Index  

Air Tank Regulators for Filling, or to Tether your Rifle & Shoot 1000's between refills

April 2 2012 at 7:53 AM

  (Login n6yyo)
YFOT


Regulators not only allow one to fill an airgun more safely, but also allow tethering, with means you can shoot 1000s of shots without refilling your airgun. Lately I have been making these dual purpose regulators for Nitrogen Air Hose Assemblies and also for use with my Air Tanks.

Buy any of my Air Hose Assemblies (Just a few of the types I offer are shown below SCBA, DIN300, Yoke, Nitrogen)) and buy a regulator for only $299. You will probably need to buy a gauge to go on it for $39 extra (depends on what kind of assembly you buy to put it on). Fill your tank more safely, or shoot your airgun on the tether and get thousands of shots without refilling from a Great White or SCBA tank.

For orders or information, please EMAIL OR CALL 714-612-5956 from 8AM-8PM Pacific

scbaassy_small.jpgdin300assy_small.jpgIMG_7702_small.JPGnitroassy_small.jpg

2011-12-02_10-59-04_386.jpgdin300regulated.jpg


NOTE: All prices are adjusted to show Forum Reader Discounts. If you read it on the Yellow, make sure you mention it when you call me or send an email. Note: I am easiest to reach after 5pm Pacific on Weekdays, or 8AM-8PM Sat-Mon (Except Sun Morning)


More information below:


AIR HOSES, FITTINGS, ADAPTERS for SCUBA DIN300 or YOKE, SCBA, Shoebox Compressor, Nitrogen
PLEASE DO NOT CLUTTER THE CLASSIFIEDS VIA A REPLY TO THIS POST! Please EMAIL

Thank you, Joe


My tank valve fittings are quality stainless steel hand-tight fittings, (no tools necessary to remove) gauges are stainless steel and liquid filled and read in both PSI and BAR, the bleeders are high quality stainless steel with a large thumb wheel to bleed. All hoses are microbore, and are the only type sold with a strain relief and steel fittings at each end. The hose is 3 foot long and only 0.070" in diameter for minimal air waste and are rated +6,000 PSI Working pressure and +20,000 PSI burst. The hose terminates in a Foster type female quick disconnect (fits Daystate, Crosman, etc.) Everything is top notch and I have over 100 feedbacks (all positive) on the BOI.




HOSE ASSEMBLIES




[linked image] Firehouse/SCBA HOSE ASSEMBLY

Highest Quality Stainless Steel Hand Tight SCBA fitting, Stainless Steel Bleeder, Stainless Steel Glycerin Filled Gauge with BAR & PSI Scales and Micro-bore hose that is only 0.070 inch ID. Each end of the microbore hose has a strain relief to help eliminate damage at each end. Includes a Stainless Steel "Foster" type female quick fill on the end. = $159 Rated to 6900 PSI.



[linked image] DIN300 SCUBA HOSE ASSEMBLY
Same as above with high quality hose rated at +6900 PSI, stainless steel Hand Tight DIN300 fitting, stainless steel female quick disconnect and stainless steel bleeder, Stainless Steel Glycerin Filled Gauge with BAR & PSI Scales, and microbore hose with strain relief at each end as our SCBA Hose Assembly, etc., but made for use with DIN300 SCUBA tanks (Rated +4500 PSI) or other type of Carbon Fiber air tanks (not fireman type). This is a great replacement for hose those who currently have a 4500 PSI SCUBA tank. $159 + $14.50 shipped priority mail and insured.




[linked image]SCUBA YOKE HOSE ASSEMBLY
Same as above with high quality hose, stainless steel disconnects and bleeder, Glycerin Filled Gauge that reads both PSI and BAR, and microbore hose with strain relief at each end, etc., but made for use with SCUBA tanks with SCUBA Yoke/Block.

Note: Most SCUBA tanks and Yoke are only rated to 3000 PSI. This is the heaviest duty Yoke made and is the ONLY one rated to 4000 PSI. It is extremely sturdy (The nicest I've seen).

Normally $169,only $139 (no tank purchase necessary).

[linked image] HAVING TROUBLE FINDING A SOURCE OF 4500 PSI AIR FILLS?
NITROGEN HOSE ASSEMBLIES MADE IN USA! Nitrogen tanks are readily available at most welding supply shops and they are cheap to rent! Also, they are 6000 PSI, so you get an amazing amount of fills. If you wish to fill your Carbon Fiber tank or air gun from a large Nitrogen tank, this is it. STAINLESS STEEL tank fitting, STAINLESS STEEL Glycerin Filled Gauge that reads BAR & PSI, Highest Quality STAINLESS STEEL Bleeder with easy to turn knob and 40" x 0.070 inch ID micro-bore hose with strain relief at each end and STAINLESS STEEL "Foster" type quick fill = $169 + $14.50 shipped priority mail and insured.


[linked image] OWN A SHOEBOX COMPRESSOR? Want to fill your tank with the best setup available? Connect your Shoebox compressor to your airtank easily and safely with this setup.
A very High Quality Bleeder, BAR/PSI Scale Liquid-Filled Gauge, 3 Ft MicroBore Hose with Stainless Steel Female Quick Disconnects on each end. All this for only $139




SCUBA, SCBA, Nitrogen and other Hose Assemblies are also available as a Cascade systemfor 2 or more tanks. See my website for more information on custom hoses, etc. Two 44 Cu Ft tanks can actually be better than one 88 Cu Ft tank when cascaded together with this system. SCBA shown on Left, SCUBA Yoke on right (also available in DIN300, and other fittings). Can also mix a SCUBA tank to bulk fill the airgun, and an SCBA to top it off or any other combination you want. Made in such a way that you can cascade 2 tanks for home use, or use just one tank (such as if you are going in the field)
[linked image]IMG_3008-2_small.JPG




Regulated Hose Assemblies. Available for SCUBA, SCBA, Nitrogen, etc. Useful for filling airguns from a 6000 PSI tank, or if you wish to shoot your rifle from a bench while tethered to your air tank so that you have a constant fill pressure (great for big bore rifles too!). Also fill your smaller air tank from a large 6000 PSI tank. Many other uses too! Comes standard with Air Filled gauges (Left), shown with optional Glycerin-Filled Gauges(Middle) Note: I sell the gauges at cost if you go for this option, its just too nice a set-up not to get them.
IMG_6529_small.JPG[linked image]regulator2.jpg



MICROBORE AIR HOSES $39 Fit Air Pumps, Hose Assemblies, etc.
I have 1, 2, and 3 foot air hoses in stock for only $39 plus $6 ship, and 5 Ft (slight additional) (BUT YOU MUST MENYION THE FORUM). These come with 1/4" or 1/8" NPT or BSPP, NO ADAPTERS NEEDED, so you waste less air.

Rated at +6000 PSI and only 0.070" diameter with strain relief at each end. These hoses are so small in diameter, that compared to the one foot of paintball hose, you could use 12 feet of this hose and still save air!

(Left) Shown with optional DIN300 Male and Female Quick Disconnect on each end for use with many carbon fiber tanks. (Right) Shown with optional Female Quick Disconnect
[linked image]> [linked image]


REDUCED: Air Hose & Extensions with Stainless Steel Male and Female Quick Disconnects.


Note: I ordered a huge amount of Stainless Steel fittings, and so I am offering almost a $40 discount on my Air Hose Extension with Stainless Steel Male and Female ("Foster" type) Quick Disconnects. Normally these would be $107, I am offering these for $69 plus $6 shipping.

This is 3 Foot long with Stainless Steel Female and Male "Foster" type quick disconnects on either end as seen here. (Most popular is the 3 foot hose, but other sizes available). Also available with other types of connectors as well, please email or call for more information.
[linked image]





If you prefer to fill your tank at a SCUBA shop that doesn't have an SCBA adapter, we have that adapter. If you want to fill it at a place that fills paintball tanks, we have that adapter too. We have all kinds of adapter and fittings, so please check out our websihttp://www.hamcontact.com/airgun/HoseAssembly/



Note: All adapters are described from left side to right.







[linked image] DIN300 (SCUBA) to Hand Tight Stainless Steel SCBA Fitting. For filling SCBA tanks at a SCUBA Dive Shop. $89



[linked image] Yoke (SCUBA) to Hand Tight Stainless Steel SCBA Fitting. $89



[linked image] Stainless Steel Male Paintball (Foster type) to Hand Tight Stainless Steel SCBA Fitting. For filling SCBA tanks at places that fill paintball tanks $79.



[linked image] Fire House Adapter = Male DIN300 (SCUBA) Hand Tight to Stainless Steel Male SCBA Fitting. Good for two uses. 1) For using my high quality hoses with a SCUBA tank, or 2) for filling SCUBA tanks at a fire house. Note: These are NOT brass fittings, nor do they require a wrench. Just hand-tighten onto your tank and you are ready to go.



[linked image] Stainless Steel Male Paintball to Male Paintball Fitting.



IMG_1875_small.jpgStainless Steel 1/8" Male NPT to Male Paintball Quick Disconnect (Left)
Stainless Steel Female Paintball Quick Disconnect to 1/8" female NPT(right) $39 for the mated pair in Stainless Steel.



IMG_1875_small.jpgStainless Steel 1/8" Male NPT to Male Paintball Quick Disconnect (Left)
Stainless Steel Female Paintball Quick Disconnect to 1/8" female NPT(right) $39 for the mated pair in Stainless Steel.


IMG_2703_small.JPGStainless Steel Female Paintball Quick Disconnect to 1/8" Female NPT. All one piece, MADE IN USA, not Asian knock-offs


IMG_2702_small.JPGStainless Steel Female Paintball Quick Disconnect to 1/8" Male NPT



IMG_2699_small.JPGStainless Steel Male Paintball Quick Disconnect to 1/8" Male NPT $19.




[linked image]Male Paintball Quick Disconnect to 1/8" Female NPT $19.



IMG_4413crop_small.JPGDead Head (No, Not the Jerry Garcia type, the kind you put on the end of a SCUBA tank's hose to determine your remaining tank pressure). Now in Stainless Steel instead of brass $19



[linked image][linked image]
(LEFT) 2.5" Stainless Steel, Glycerin-filled Gauge with PSI & BAR readout and 1/4" NPT $39. Also available for Hill Pumps etc., only $49 Fit other Airtanks, like the Korean, etc. for $69. This gauge is made in America, as is most of my product.

(RIGHT) READ THE PRESSURE OF YOUR SCUBA or SCBA TANK WITH THIS GAUGE. If you would like an accurate gauge, that reads in BAR and PSI to easily measure the pressure inside your airtank, this is it. Just connect the male "Paintball/Foster" type Male Quick Disconnect to your air hose, and that's it! Only $59.



[linked image][linked image] 1" (23mm) High Quality Metal Gauge with BAR readout. Excellent replacement for most air guns, air tanks, etc. These are very nice gauges, not like paintball stuff.
Available in 1/8" BSPP back mount $35



[linked image]

PROBE ADAPTERS



[linked image] Dowdy Seal with 1/8" Female BSPP to Male Quick Disconnect (Fits FX, newer Air Arms, etc.)



IMG_1404_small.JPG Steel 1/4" Female BSPP to Stainless Steel Male Quick Disconnect, seals with Delrin insert (Fits Condor/Talon, etc.). Air Force Condor/Talon bottle to Stainless Steel Male Quick Disconnect Adapter. Available as shown as complete adapter to fill an Air Force bottle from either your pump, air tank or any hose that has a Female Quick Disconnect, or I have just the proper male quick disconnects if you already have the Condor Adapter.



IMG_0247_small.JPG JIC Fitting to Male Quick Disconnect, seals with taper (Fits older Korean Air Guns, I.e. Career, etc.)


[linked image] One Pieces DIN200 to Male Paintball Quick Disconnect (Fits Steyr, Feinwerkbau, etc.) $39







Theoben Rapid Quick Fills

I am advertising 2 kinds of quick fills.

The first is an in-stock quick fill for Theoben Rapids. No longer will you need to unscrew the bottle one turn, burp the action for a few shots, remove the bottle, find then get a wrench for your bottle adapter, fill the bottle, and screw the bottle back on the rifle. Now, with this in-stock fill all you need to do is hook up the female quick disconnect to your hose directly to this male on the rifle. These are great!

Just screw this into the bottom of your Theoben Rapid and then you can just attach the Female Quick Disconnect of your hose directly to your Rapid! In addition, you wont lose the air it takes to re-pressurize the action when re-installing the bottle. (This picture is outdated. Adapter is now steel, and Male Quick Disconnect is upgraded to Stainless Steel Male, so it wont wear out. Everything you need, Dowdy Seal, Threaded Fitting and Male Quick Disconnect is included $59



[linked image][linked image]

In addition, I also have the female connector for Allen Z Bottle quick disconnect he mounts on Rapids, Feinwerbau, Stey, etc., as well as the older Air Arms S300, S310, S400, S410 that use the "air chuck" instead of the banjo type (picture below is worth a 1000 words). Only $35



[linked image][linked image]




Joe Brancato 714-612-5956

For AirTanks, Custom Hoses, Fittings, Gauges, etc.
please click here http://www.AirTanksForSale.com
[linked image]

 
 Respond to this message   
Current Topic - Air Tank Regulators for Filling, or to Tether your Rifle & Shoot 1000's between refills
  << Previous Topic | Next Topic >>Return to Index  



BKL MOUNTS - SECOND TO NONE.


James Kitching Memorial Page

D I S C L A I M E R
JK's Airgun Forums, moderators, and administrators are not responsible for any problems that may occur from buying or selling products posted on this page, as they are the exclusive responsibility of two parties: the person who sold and the person who bought posted items.JK's Airgun Forums, moderators, and administrators are not responsible for any problems that may occur from reading or using content posted on this forum, as they are the exclusive responsibility of two parties: the person who posted it and the person who acted on said posted information.Use of our forums by people under 18 years old is allowed only with legal guardian(s) present..