tv repair shop software
 

Software for repair shop
Assist Control



Free trial

tv repair

 Monitor repair forum - Open   
Download schematics and service manuals
See our courses below


 
       
 


  << Previous Topic | Next Topic >>Go to monitor repair course  

daewoo cmc 518x FCC-ID C5F7NFCMC1518X

November 12 2002 at 2:57 PM
No score for this post
schroder  (Login schroder)

 
S/C HOT IN ABOUT 5 SECONDS WITH OUT IT GETTING WARM.

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
AuthorReply
Syl
(Login sylvaro)

Same monitor...

No score for this post
November 13 2002, 7:20 PM 

I have the same monitor. Supply was dead so I replaced the main Mosfet that was all shorted (2SK2333) but supply still refuses to start.
Anyone has a schmeatic for that thing ?

Sylvain

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
Syl
(Login sylvaro)

found another bad part...

No score for this post
November 13 2002, 8:25 PM 

found another bad part...
IC002 in the power supply. KA3842B dead short between pin 7 and 5.

Now I have to find another part.
Wish me luck.

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
Tom
(no login)

Schematic

No score for this post
January 24 2003, 1:08 AM 

Having the same problem. I have a schematic. Did the ic002 solve your problem?

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
Syl
(Login sylvaro)

518 monitor

No score for this post
January 24 2003, 9:32 AM 

I unsoldered a 3842 from another monitor and it still wouldn't start.
I ordered brand new parts from Mouser and when I get them I will try it again...

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
Repairs Online
(no login)

Re: 518 monitor

No score for this post
December 21 2004, 11:30 PM 

Hello,

Check IRF644, very close to HOT, for short/open circuit. This is the same model as HP, Model:D2827A, Chassis: 518X

In addition to HOT, BU2520DX and IRF644 been short circuited. I get continuiuty readings between primary (pins 1 & 2) with pins 3 and 4.

As I don't have a schematic of this chassis or flyback or the HR equivalent, would someone advice me if this is normal.

Sincerely
Repairs Online

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
Samir Shah
(no login)

Dead Monitor D2827A

No score for this post
March 7 2006, 7:23 AM 

I need a schematic for this model which has FCC Id C5F7NFCMC1518X.
My problem was dead Monitor with HOT C5296 shorted Chassis worked ok when it was disconnected from yoke but was tripping On/Off when connected and then HOT blew out again.
Any suggestions are appreciated.
Thanks.
Samir

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
p.k.gupta
(no login)

need schematic

No score for this post
March 15 2006, 1:09 AM 

i need the schematic for thie send email.
also plaease let me know i also need schematic for hp cmc 1516x/1340x.
please snd email at
linus_impex@yahoo.com
thanks
pk gupta

 
Scoring disabled. You must be logged in to score posts.Respond to this message   
 
  << Previous Topic | Next Topic >>Go to monitor repair course  
Find more forums on SchoolsCreate your own forum at Network54
 Copyright © 1999-2018 Network54. All rights reserved.   Terms of Use   Privacy Statement  
   TV repair course   TV repair forum     Monitor repair forum    Monitor repair course